Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
They are making a number of good points about How to Install a Bathtub overall in the content further down.
Installing a bathtub isn't precisely rocket science, but it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately difficult project. If the old bathtub is conveniently accessible, the job can relocate rapidly; if you have to open a wall to get rid of the old tub and position the brand-new tub, the task is a lot harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as set in the brand-new one. Ensure you have certified on your own for the task as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is far better to think about using one before you start. Opportunities are you may require a professional plumber to make tube connections.
This post will certainly assist you mount a brand-new bath tub in your restroom if you have actually already purchased a new bathtub and also do not require to transform the setup of your previous water supply pipes.
Your tools as well as material list must make up the following:
Getting ready for the Installation
Firstly, the sustaining frame supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is separate the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be quite troublesome because of the restricted gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Installing the Tub
Making use of the two wood boards under its feet, place the bathtub in the needed placement. The wood boards are handy in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the spirit level reads level.
To set up taps, fit the bottom of the furthest adaptable tap connector to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
Turn on the water and also inspect all joints and new pipework for leaks and tighten them if needed. Fill the bath tub and also check the overflow outlet and the regular outlet for leaks.
Finally, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and sealing around the tub should wait up until the bath tub has actually been used at least when as this will resolve it right into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washing machines remain in place in between the tap and the sink. Secure the tap in position with the maker supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, leading to complications with wetness and also possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was introduced to that article about Installing A Bathtub through an acquaintance on a different web address. Sharing is good. Helping others is fun. Thanks a lot for your time. Visit again soon.
Schedule Here Report this page